Looking for:
How to manually vacuum pool |
How to manually vacuum pool.Here’s How To Vacuum Your Pool Manually In 3 Easy Steps
These are pretty neat. Pressure-side pool cleaners run off the return line from your pump so all of that water pressure getting pumped back into your pool is actually put to good use. These guys can scrub, vacuum, and move around your pool all on their own.
They usually require filter bags and sometimes separate connections to get them all set up perfectly. Suction-side pool cleaners get plugged into the same spot as your vacuum. About Us Privacy Policy. Free Checklist. Share on facebook. Share on twitter. Share on pinterest. Share on linkedin.
Pool Care , Pool Maintenance. The first step is to open your telescopic pool rod to the length needed to vacuum your pool. It should generally be about five to six feet longer than the depth of your pool, so for an 8-foot pool, you should use a thirteen to fourteen-foot pole. Attach the vacuum head to the end of the telescopic pole. Make sure the tabs are pressed down, and then slide the telescopic pole into the slot until the tabs click into place in the holes on the telescoping pole.
Attach the hose to the pool vacuum and submerge the contraption and all of the hose into the water. Place the other end of the hose against one of the return jets and wait until bubbles stop appearing at the vacuum end.
Make sure to fill the entire vacuum hose with water to prevent air bubbles from forming. Finally, either insert your pool hose with a skimmer plate into the skimmer or remove the skimmer basket and insert the hose directly into the skimmer port. Once the hose is connected, you should notice constant suction from your pool vacuum. Now it is time for the real work; let the vacuuming commence!
Manually vacuuming your pool is no easy task. Especially with high suction, you are in for quite an arm workout. You should always start in the shallow end and work your way deeper along the pool floor because debris is more likely to make its way down to the bottom of the pool towards the deep end. Take your time as you push the vacuum around — this is not a race. Slowly push the vacuum along the pool floor and pay attention to the surfaces to ensure that you effectively remove all debris.
More than likely, vacuuming will leave your pool murky because of all the disturbed debris floating around the pool water. If this happens, give the water a couple of hours to settle and come back to vacuum the rest later.
Once you have vacuumed the pool, wait a few hours for the stirred-up particles to settle and go over the pool again with the vacuum. Then disassemble the manual vacuum by removing the vacuum head and hose and draining the remaining water in the hose. If you choose to use a sand filter as your vacuum filtration method, you'll just need to choose the proper setting.
Usually this type of filter system will have six settings: rinse, recirculate, backwash, waste, filter or closed. The filter setting is the most common setting used to vacuum a pool. It will handle minimal debris with no visible algae. But if your pool water is a little dirtier than normal, choose the waste setting. Other methods of cleaning these pools are preferred and a more extensive algae cleaning may be necessary.
It will minimize algae and help you maintain normal PH levels, making your maintenance a little less time-consuming. To keep your pool sparkling-clean and clear, you'll need to use an extra cleaning method at least once a week. After a few weeks of manually scrubbing and vacuuming your pool, you'll probably agree that an automatic pool cleaner is a worthy investment to free up your time and energy.
There are a few different types to choose from, and what works for you will be dependent on your particular situation and preference. I recommend a robotic cleaner for large pools or pools with hard-to-reach areas as most can be operated by remote control.
A suction-side cleaner attaches to your pool filter to create suction. A pressure-side cleaner attaches to the return hose on your pool filter for suction and has its own collection bag. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Manual vacuuming is like the deep-cleaning step which helps the other cleaning process like skimming.
You can include it in your regular maintenance and the fight of the algae problem. The first step is — of course — assembling all of the tools needed. You have to properly assemble them to avoid the obstacles that may happen during the cleaning process.
To run the vacuum system, you need up attach it to the skimmer inlet which is powered by the circulation pump of the pool.
Comments
Post a Comment